Microcom Technologies Commander General Purpose Variable Speed Drive GpLV Manual do Utilizador Página 75
- Página / 118
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Commander GP User Guide
Issue code: gpxu2
Setting Up the Drive 3-47
Ramps
Acceleration
rate
Deceleration
rate
FREQUENCY TORQUE
Motor control
Current
limit
Synchronize
to a spinning
motor
Motor
active-current
0.39
0.03
0.04
Pre-ramp
reference
Post-ramp
reference
0.11 0.12
0.06
No. of poles
Power factor
Rated voltage
Rated speed
Rated current
Rated frequency
PWM switching
frequency
0.41
0.42 ~ 0.47
Motor parameters
0.13
Power stage
9 10
THERMISTOR
830
EXTERNAL TRIP
Voltage mode
selector
Dynamic V/f
select
0.07
Boost voltage
0.08
0.09
Motor-voltage control
Estimated
motor
speed
0.10
0.31 Macro number
0.32 Serial comms. mode
0.33 Drive rated current
0.34 User security code
0.36 Serial comms. baud rate
0.37 Serial comms. address
0.40 Autotune
0.48 Drive operating mode
selector
0.49 Security status
0.50 Software version number
Other parameters
0.XX
0.XX
X X
X X
Key
Read-write (RW)
parameter
Read-only (RO)
parameter
Input terminals
Output terminals
The parameters are shown at their default settings.
The logic diagram is valid when all parameters are
at their default settings but may not be valid when
certain parameters are adjusted.
- COMMANDERGGpp 1
- COMMANDERGGpp LVLV 1
- General information 2
- Important 2
- Contents 3
- Commander GP User Guide 4
- Issue code: gpxu2 4
- 1 Introduction 5
- 1.3 Configuration layers 6
- 1.4 Default configurations 6
- 1.5 Operating mode 6
- 1.6 User-interface modes 6
- 1.7 Macro configurations 7
- 1.8 Plug-in option modules 8
- 1.9 Serial communications 8
- Introduction 1-5 9
- 1-6 Introduction 10
- 2 Getting Started 11
- 2-2 Getting Started 12
- Getting Started 2-3 13
- 2-4 Getting Started 14
- Getting Started 2-5 15
- 2.3 Introduction to the 16
- 2.4 Working with 17
- 2.5 How macro configurations 18
- 2.6 Initial setting up 19
- 2-10 Getting Started 20
- Enabling Macro 1 20
- Getting Started 2-11 21
- 2-12 Getting Started 22
- Autotune 22
- 2.7 Operating instructions 23
- 2-14 Getting Started 24
- Keypad mode 24
- Trip and enable 24
- Getting Started 2-15 25
- Acceleration rate 25
- Deceleration rate 25
- Braking resistor 25
- 2-16 Getting Started 26
- Voltage-control modes 26
- Getting Started 2-17 27
- Boost voltage 27
- 2-18 Getting Started 28
- 3 Setting Up the Drive 29
- (Macro Configurations) 29
- General purpose 30
- Setting Up the Drive 3-3 31
- 3-4 Setting Up the Drive 32
- Setting Up the Drive 3-5 33
- 3-6 Setting Up the Drive 34
- Setting Up the Drive 3-7 35
- Setting up and using Macro 0 35
- 3-8 Setting Up the Drive 36
- Easy mode 37
- 3-10 Setting Up the Drive 38
- Setting Up the Drive 3-11 39
- 3-12 Setting Up the Drive 40
- Setting Up the Drive 3-13 41
- Setting up and using Macro 1 41
- 3-14 Setting Up the Drive 42
- Motorized potentiometer 43
- 3-16 Setting Up the Drive 44
- Setting Up the Drive 3-17 45
- 3-18 Setting Up the Drive 46
- Setting Up the Drive 3-19 47
- Setting up and using Macro 2 47
- 3-20 Setting Up the Drive 48
- Preset frequencies 49
- 3-22 Setting Up the Drive 50
- Setting Up the Drive 3-23 51
- 3-24 Setting Up the Drive 52
- Setting Up the Drive 3-25 53
- Setting up and using Macro 3 53
- 3-26 Setting Up the Drive 54
- Torque control 55
- FREQUENCY CONTROL 55
- TORQUE CONTROL 55
- 3-28 Setting Up the Drive 56
- Setting Up the Drive 3-29 57
- 3-30 Setting Up the Drive 58
- Setting Up the Drive 3-31 59
- Setting up and using Macro 4 59
- 3-32 Setting Up the Drive 60
- PID (set-point control) 61
- PID CONTROL 61
- 3-34 Setting Up the Drive 62
- Setting Up the Drive 3-35 63
- 3-36 Setting Up the Drive 64
- Setting Up the Drive 3-37 65
- Setting up and using Macro 5 65
- Axis-limit control 66
- Setting Up the Drive 3-39 67
- 3-40 Setting Up the Drive 68
- Setting Up the Drive 3-41 69
- 3-42 Setting Up the Drive 70
- Setting Up the Drive 3-43 71
- Setting up and using Macro 6 71
- 3-44 Setting Up the Drive 72
- Brake control 73
- 3-46 Setting Up the Drive 74
- Setting Up the Drive 3-47 75
- 3-48 Setting Up the Drive 76
- Setting Up the Drive 3-49 77
- Setting up and using Macro 7 77
- 3-50 Setting Up the Drive 78
- A Programming 79
- Instructions 79
- A-2 Programming Instructions 80
- A.6 Selecting 81
- A.7 Changing the value of a 82
- Programming Instructions A-5 83
- A-6 Programming Instructions 84
- A.13 Restoring the Drive 85
- A-8 Programming Instructions 86
- B Security 87
- B-2 Security 88
- C Signal Connections 89
- C-2 Signal Connections 90
- Signal Connections C-3 91
- C-4 Signal Connections 92
- D Menu 0 Parameters 93
- D.2 Fixed-function parameters 94
- Menu 0 Parameters D-3 95
- D-4 Menu 0 Parameters 96
- Voltage boost 96
- PWM switching frequency 98
- Menu 0 Parameters D-7 99
- Motor parameters 99
- Drive software build number 99
- Status information 99
- D.3 Parameters specific 100
- Menu 0 Parameters D-9 101
- D-10 Menu 0 Parameters 102
- Menu 0 Parameters D-11 103
- D-12 Menu 0 Parameters 104
- Menu 0 Parameters D-13 105
- D-14 Menu 0 Parameters 106
- Menu 0 Parameters D-15 107
- D-16 Menu 0 Parameters 108
- Menu 0 Parameters D-17 109
- D-18 Menu 0 Parameters 110
- Menu 0 Parameters D-19 111
- D-20 Menu 0 Parameters 112
- Menu 0 Parameters D-21 113
- D-22 Menu 0 Parameters 114
- E Diagnostics 115
- E.3 Trip codes 116
- Diagnostics E-3 117
- E-4 Diagnostics 118
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais